Sale!

Holybro Kakute F7 AIO V1.5 Flight Controller OSD PDB+Atlatl HV V2 5.8G FPV Transmitter for RC Drone

25,840.01

Be Quick! Just 3 items left in stock with FREE delivery

Prices go up when the timer hits zero.

3 in stock

SKU: 1317568 Category:

Description

Holybro Kakute F7 AIO V1.5 Flight Controller OSD PDB+Atlatl HV V2 5.8G FPV Transmitter for RC Drone

Specification:

Kakute F7 flight controller:
Click For Kakute F7 AIO V1.5  Manual 

•MCU: STM32F745 32-bit processor
• IMU: MPU6000 (SPI)
• Barometer: BMP280
• Current Sensor: Approximately 130 amps maximum measurable value
• USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
• 6 hardware UARTS (UART1,2,3,4,6,7)
• All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on 
any UART without “uninvert hack”.
• Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not 
supported.
• TF card for Blackbox logging
• Dimensions: 35x41x7mm (includes foam-mounted gyro board in height)
• Mounting Holes: Standard 30.5mm square to center of holes
• Weight: 8g

Features:

Supports Betaflight, Butterflight, and Cleanflight.
• Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video 
transmitter channel and power level, all using your transmitter sticks and goggles.
• Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating 
foam. This means that there is no need to soft-mount the board itself.
• High-performance / low-noise / high sensitivity IMU. MPU6000 with 6-axis gyro and 
accelerometer. 
• Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with 
external GPS/magnetometer units.
• Dedicated bootloader button for easy firmware flashing.
• Low-profile design fits into even very compact frames.
• Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad 
only).
• Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the 
Kakute F7 V1.5 monitors voltage directly from the power supply.
• Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2
amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV 
camera, or LED strip.
• Supports BLHeli pass-through for easy ESC upgrade and configuration.
 

Atlatl HV V2:
Click For Atlatl HV V2 Manual

•Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
• Audio: 6.5 MHz Mono
• Antenna Connector: MMCX
• Input Voltage: 7 to 28 volts (2-6S LiPo) with absolute maximum 42 volts
• Dimensions: 35x25x7mm (Includes USB height)
• Mounting Holes: Standard 30.5mm square to center of holes
• Weight: 9.3g

Features:Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc.
• Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband.
• SmartAudio input allows remote control by the flight controller. Change channel, transmit
power, and more from Betaflight OSD, flight controller USB port, Taranis Lua Script, and more.
• All parameters are controllable via push-button on the side of the unit, for cases where
SmartAudio is not used.
• MMCX connector is durable and easy to use. Rated for 100’s of mating cycles. Easy and quick
antenna changes. No more ripped-off UFL connectors.
• LED indicators for channel, band, and power. Allows easy check of vTX parameters simply by
glancing at the quad.
• Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch
to 800 mW for freestyle.
• 0.5 mW True Pit Mode allows you to power up safely without the risk of knocking other pilots
out of the air.
• Built in microphone, so you can listen to your motors while you fly, no matter how far away you
fly.
• Standard 36mm form factor allows you to mount the Atlatl directly on your flight controller
stack
 

Package included:
1x Kakute f7 AIO V1.5 +Atlatl V2 stack 
1x 80mm SMA–MMCX Cable
1x 150mm 4pin JST GH wire

Reviews

There are no reviews yet.

Be the first to review “Holybro Kakute F7 AIO V1.5 Flight Controller OSD PDB+Atlatl HV V2 5.8G FPV Transmitter for RC Drone”

Your email address will not be published.